Difference between revisions of "HighF v14.12"

From SCECpedia
Jump to navigationJump to search
Line 42: Line 42:
 
*[http://hypocenter.usc.edu/research/High-F/bbp1d_mid.pdf Diagram of smoothed 1D Model showing Layers (pdf)]
 
*[http://hypocenter.usc.edu/research/High-F/bbp1d_mid.pdf Diagram of smoothed 1D Model showing Layers (pdf)]
 
*[http://hypocenter.usc.edu/research/High-F/bbp1d_int_500.rtf 1D model data file (20m resolution) (rtf)]
 
*[http://hypocenter.usc.edu/research/High-F/bbp1d_int_500.rtf 1D model data file (20m resolution) (rtf)]
 
  
 
Definition of Los Angeles Basin 1D velocity models used in the Broadband Platform project:
 
Definition of Los Angeles Basin 1D velocity models used in the Broadband Platform project:
Line 55: Line 54:
 
**[http://hypocenter.usc.edu/research/High-F/merged_lahabra_sites.txt  Merged (SMO + SCECDC) Site List (TXT File)]
 
**[http://hypocenter.usc.edu/research/High-F/merged_lahabra_sites.txt  Merged (SMO + SCECDC) Site List (TXT File)]
  
These data are obtained from two data sources:
+
These data will be obtained from two data sources:
 
All the SMO La Habra sites (In Cosmos format): 309
 
All the SMO La Habra sites (In Cosmos format): 309
 
*[http://hypocenter.usc.edu/research/High-F/smo_sites.kml SMO (Cosmos Format) KML Site Map (KML)]
 
*[http://hypocenter.usc.edu/research/High-F/smo_sites.kml SMO (Cosmos Format) KML Site Map (KML)]
Line 64: Line 63:
 
*[http://hypocenter.usc.edu/research/High-F/scecdc_only_lahabra_sites.txt SCECDC Only Site List (TXT File)]
 
*[http://hypocenter.usc.edu/research/High-F/scecdc_only_lahabra_sites.txt SCECDC Only Site List (TXT File)]
  
[[Image:Merged smoscecdc labra sites.png|256px|thumb|right|Fig 1:Stations with Accelerometer Data for the La Habra Earthquake in Simulation Volume]]
+
[[Image:Merged smoscecdc labra sites.png|256px|thumb|right|Fig 1: 356 La Habra Earthquake ground motion accelerometer recordings for the La Habra Earthquake in Simulation Volume]]
  
 
== Simulation Box / Velocity Model ==
 
== Simulation Box / Velocity Model ==

Revision as of 04:11, 31 March 2015

This page collects information about a proposed high frequency verification and validation exercise. Planning started in Dec 2014.

Goal

Most regional scale deterministic earthquake simulation verification and validation exercises have been done at frequencies 1Hz or lower [1] [2]. With the introduction of high performance CPU and CPU-GPU wave propagation codes, there has been significant recent progress running simulations up to 4Hz. As we increase the capabilities of our deterministic earthquake simulation codes, we need to re-evaluate the codes performance at these higher frequencies that are now possible. The goal of this activity is to evaluate the performance of multiple wave propagation codes that are capable of simulation regional scale earthquakes at frequencies 4Hz+.

Approach

High frequency simulations introduce several code modifications intended to more accurately model the physics of high frequency earthquake wave propagation simulations. Modification to existing wave propagation codes to support 1Hz+ simulations include:

  • Source descriptions with energy above 1Hz
  • Small scale heterogeneities in the 3D velocity models
  • Frequency dependent attenuation
  • Near fault plastic yielding
  • Large displacement plastic yielding

To help isolate the impact of each of these changes, we propose to start with simple (possibly unrealistic) high frequency (4Hz) ground motion simulations and compare the simulation results produced by different methods. Then we will introduce these modifications one at a time, as a way if isolating the impact of each change individually.

Problem Statement

We have defined common input parameters for use by both AWP-ODC, and Hercules. The problem statements includes the following parameters:

  1. Simulation Region
  2. Source Description
  3. Station List
  4. Velocity Model
  5. Simulation Duration
  6. Simulated Frequency Range
  7. Sample per Wavelength

Simulation Region

The simulation region four corners are given in the table below:

Volume size:

  • 180,000 m x 135,000 m x 61,875 m = 1.503e15 m3

Source Description

We will use a rough-fault dynamic-rupture-based point source produced by Zheqiang Shi (SDSU) that has frequencies above 4Hz, scaled to Mw5.1 La Habra. The source is plotted and defined in the following files. These show the source trimmed, low-pass filtered (fc=5Hz, Butterworth, 2 forward passes, 4 poles), 4300 points, dt=0.001s (and plot of what is should look like).

1D Velocity Model Definition

The first velocity model will be modeled on a 1D model of the Los Angeles Basin used in on the Broadband Platform project. The model was smoothed to eliminate sharp contrasts between layers.

Definition of Los Angeles Basin 1D velocity models used in the Broadband Platform project:

Station List

We developed a list of ground motion observations for the La Habra earthquake. A description of the methods used to create this merged site list are provided at Selection of La Habra Ground Motion Observations.

This site list is based on use of publicly posted data sets for the La Habra event. There should be on-scale accelerometer ground motion data at all of these sites for the La Habra mainshock. We have not yet plotted all data to visually confirm the data is above noise, and on-scale. This list combine all channels available from SMO and SCECDC for the La Habra Event using only acceleration instruments within the simulation region:

These data will be obtained from two data sources: All the SMO La Habra sites (In Cosmos format): 309

SCECDC Only Sites: 47

Fig 1: 356 La Habra Earthquake ground motion accelerometer recordings for the La Habra Earthquake in Simulation Volume

Simulation Box / Velocity Model

Parameter Value Notes
Dimensions (km) 180 x 135 x 61.875 (31 km for 1d Model)
Bounding Box (LL) -119.288842 34.120549, -118.354016 35.061096, -116.846030 34.025873, -117.780976 33.096503
Rotation Angle 39.9
UCVM Version 14.3.0 No heterogeneities
Velocity Model Versions CVM-S4v26
Miniumum Vs 500 m/s
Samples per wavelength 6 to 7 - AWP 10 to 12 - Hercules


Point Source Parameters

Parameter Value Notes
Event Name La Habra
Mw 5.1 Ref: http://www.scsn.org/2014lahabra.html
Moment 5.764 E+23 Dyne-cm Source: En-Jui
Origin Time 2014/03/29 04:09:42.97 Source: En-Jui
Origin Location -117.930; 33.922; 5.0km Source: En-Jui
Strike/Dip/Rake 239/70/38 Source: En-Jui, based on review of aftershock sequence
Rise Time 0.75 s

Solver Parameters

Parameter Value Notes
Frequency 4.0 Hz
Simulation Length (Duration) 100 s
Delta T 0.005
Plane Output Resolution 250m
I/O Print Rate every 10 steps
Station List TBD
Software Version TBD


Fig 1:Location of La Habra Main Shock and aftershocks, used to select preferred fault plane solution. (Image Credit: En-Jui Lee)

High-F VandV Exercise Planning Documents (2015)

High-F Project Plan (2012)

Agreements Needed

  • Simulation Volumes
  • Rotation Angle
  • Projections used
  • Points per wavelength used
  • Number and location of sites used for ground motion comparison
  • Proposed Station List to save results
  • La Habra Point Source parameters
  • Currently available code capabilities in GPU codes
    • small scale heterogeneities
    • FDQ
    • Plasticity
    • dynamic rupture source
  • V and V exercise stages - need to be reviiewed and approved

Related Entries

References Used

  • Taborda, R. and J. Bielak (2013). Ground-motion simulation and validation of the 2008 Chino Hills, California, earthquake, Bull. Seismol. Soc. Am. 103, no. 1, 131–156, doi 10.1785/0120110325.