CyberShake Study 22.12: Difference between revisions
From SCECpedia
Jump to navigationJump to search
| Line 122: | Line 122: | ||
*For each validation event, calculate BBP results, CS results, and CS results with BBP Vs30 values | *For each validation event, calculate BBP results, CS results, and CS results with BBP Vs30 values | ||
*Check for spectral discontinuities around 1 Hz | *Check for spectral discontinuities around 1 Hz | ||
*Decide if we should stick with rvfrac=0.8 or allow it to vary | *<s>Decide if we should stick with rvfrac=0.8 or allow it to vary</s> | ||
*Determine appropriate SGT, low-frequency, and high-frequency seismogram durations | *Determine appropriate SGT, low-frequency, and high-frequency seismogram durations | ||
| Line 130: | Line 129: | ||
=== Technical to-dos === | === Technical to-dos === | ||
*Integrate refactoring of BBP codes into latest BBP release | *<s>Integrate refactoring of BBP codes into latest BBP release</s> | ||
*Switch to using github repo version of CyberShake on Summit | *<s>Switch to using github repo version of CyberShake on Summit</s> | ||
*Update to latest UCVM (v22.7) | *<s>Update to latest UCVM (v22.7)</s> | ||
*Switch to optimized version of rupture generator | *Switch to optimized version of rupture generator | ||
*Test DirectSynth code with fixed memory leak from Frontera | *Test DirectSynth code with fixed memory leak from Frontera | ||
*Switch to using Pegasus-supported interface to Globus transfers | *Switch to using Pegasus-supported interface to Globus transfers | ||
*Test bundled glide-in jobs for SGT and DirectSynth jobs | |||
== Presentations, Posters, and Papers == | == Presentations, Posters, and Papers == | ||
Revision as of 19:41, 29 August 2022
CyberShake Study 22.10 is a proposed study in Southern California which will include deterministic low-frequency (0-1 Hz) and stochastic high-frequency (1-50 Hz) simulations. We will use the Graves & Pitarka (2019) rupture generator and the high frequency modules from the SCEC Broadband Platform v22.4.
Status
This study is in the planning phase. We estimate calculations will begin in October 2022.
Data Products
Science Goals
Technical Goals
Sites
Velocity Model
High-frequency codes
For this study, we will use the Graves & Pitarka high frequency module (hb_high) from the Broadband Platform v22.4, hb_high_v6.0.5. We will use the following parameters. Parameters in bold have been changed for this study.
| Parameter | Value |
|---|---|
| stress_average | 50 |
| rayset | 2,1,2 |
| siteamp | 1 |
| nbu | 4 (not used) |
| ifft | 0 (not used) |
| flol | 0.02 (not used) |
| fhil | 19.9 (not used) |
| irand | Seed used for generating SRF |
| tlen | Seismogram length, in sec |
| dt | 0.01 |
| fmax | 10 (not used) |
| kappa | 0.04 |
| qfexp | 0.6 |
| mean_rvfac | 0.775 |
| range_rvfac | 0.1 |
| rvfac | Calculated using BBP hfsims_cfg.py code |
| shal_rvfac | 0.6 |
| deep_rvfac | 0.6 |
| czero | 2 |
| c_alpha | -99 |
| sm | -1 |
| vr | -1 |
| vsmoho | 999.9 |
| nlskip | -99 |
| vpsig | 0 |
| vshsig | 0 |
| rhosig | 0 |
| qssig | 0 |
| icflag | 1 |
| velname | -1 |
| fa_sig1 | 0 |
| fa_sig2 | 0 |
| rvsig1 | 0.1 |
| ipdur_model | 11 |
| ispar_adjust | 1 |
| targ_mag | -1 |
| fault_area | -1 |
| default_c0 | 57 |
| default_c1 | 34 |
Verification
Updates and Enhancements
Output Data Products
Computational and Data Estimates
Lessons Learned
Stress Test
Performance Metrics
Production Checklist
Science to-dos
- Perform validation for Northridge, Chino Hills, Whittier, Landers, Hector Mine, and North Palm Springs
- For each validation event, calculate BBP results, CS results, and CS results with BBP Vs30 values
- Check for spectral discontinuities around 1 Hz
Decide if we should stick with rvfrac=0.8 or allow it to vary
- Determine appropriate SGT, low-frequency, and high-frequency seismogram durations
- Update high-frequency Vs30 to use released Thompson values
Technical to-dos
Integrate refactoring of BBP codes into latest BBP releaseSwitch to using github repo version of CyberShake on SummitUpdate to latest UCVM (v22.7)- Switch to optimized version of rupture generator
- Test DirectSynth code with fixed memory leak from Frontera
- Switch to using Pegasus-supported interface to Globus transfers
- Test bundled glide-in jobs for SGT and DirectSynth jobs
