VShaker

CME team at SCEC can produce forward wave propagation data – ground motion time-histories (seismograms) for simulated earthquakes of various magnitudes. The largest, full dynamic earthquake simulation of magnitude 8 on southern San Andreas fault was led by SCEC last year. The seismograms produced by this simulation included frequency components up to 2 Hz. These seismograms can be applied to steel buildings models in virtual environment with Frame3D software, a building analysis program developed by Swaminathan Krishnan at California Institute of Technology. Frame3D allows us to perform efficient three-dimensional nonlinear analysis of steel buildings subject to ground acceleration records.

Fig 1: Building Sites

We needed a package to interface ground motion data with structural analysis software to visualize building response to ground motion time-histories. VShaker is set of tools developed at SCEC to provide this interface. It provides formatted ground motion time-history input to Frame3D software, process and visualizes its output data. The building analysis results from Frame3D are processed by VShaker program in two steps. The program first combines structural model, response data from Frame3D and ground motion data to build three-dimensional geometric representations of the structure at specified time intervals. These geometric representations are output as Wavefront OBJ files - a universal file format supported by major 3D rendering programs. In the next step VShaker can combine these snapshots to produce simple animations of structural motion with various viewpoints.

Fig 2: 18-Story Northridge building (Front view).

Fig 3: 18-Story Northridge building (Side view).

Fig 4: 18-Story Northridge building (Top view).

We are currently conducting a study to evaluate the response of two types of steel buildings with fundamental periods of 0.63 and 4.54 seconds subjected to acceleration records from SCEC M8 Simulation. These buildings are being simulated at eight locations spread out across Southern California. The locations were chosen based on a previous study conducted by Krishnan et al., on response of tall steel buildings for magnitude 7.9 1857 southern San Andreas Earthquake. The choice of building locations will allow us to compare the results of building response from our study to those reported in the earlier study. The tall steel building with fundamental period of 4.54 seconds had comparable responses to those reported in Mw 7.9 earthquake study.

VShaker has the potential to produce animations of structural motion after significant earthquake to aid in identification of damage to structural elements. It can also be used to effectively visualize performance of proposed building models to simulated earthquakes.

Caltech Virtual Shaker

• Caltech Civil Engineering Frame3D
• Caltech Virtual Shaker
• Building Design for M8 Study

SCEC Virtual Shaker Development

• Building Response to M8 in Northridge (59MB movie of building response in .mov format)

• Locations of Tall Buildings in Los Angeles in KML format

M8 Building Response Study

Building used in M8 response study is described here:

• Building In Use

Building Sites:

• Site 1: Thousand Oaks (34.18750, -118.87500)
• Site 2: Northridge (34.21875, -118.53125)
• Site 3: West Los Angeles (34.03125, -118.40625)
• Site 4: Downtown Los Angeles (34.06250,-118.25000)
• Site 5: Baldwin Park (34.09375, -118.00000)
• Site 6: Anaheim (33.84375, -117.90625)
• Site 7: Long Beach (33.78125, -118.18750)
• Site 8: Santa Ana (33.75000, -117.87500)

M8 Collaborator Sites:

• Site 9: California Institute of Technology (34.137419,-118.124432)
• Site 10: San Diego Supercomputer Center (34.01940,-118.28619)
• Site 11: SCEC/USC (32.881211,-117.235283)
• Site 12: San Diego State University ( 32.776482,-117.069001)

Information on the SCEC M8 Simulation:

• M8 Data on Websims
• M8 Project Home Page

M8 seismograms used in Building Response Study from Websims

• Websims

Fig: Los Angeles are locations of Tall (>20Story) Buildings

Software Design

• VShaker_Metadata
• Convert Virtual Shaker output to OBJ Files.
• Map damage data from Virtual Shaker Results to OBJ meshes.
• Render OBJ files.

Documents

• VShaker M8 Building Response Poster
  Error creating thumbnail: convert: unable to extend cache `/tmp/magick-8478_QnQ60DcnrtC': File too large @ error/cache.c/OpenPixelCache/4091. convert: no images defined `/tmp/transform_ed8364bb7110.jpg' @ error/convert.c/ConvertImageCommand/3229.