Difference between revisions of "CyberShake Study 22.12"

From SCECpedia
Jump to navigationJump to search
Line 144: Line 144:
  
 
{|
 
{|
| [[File:SBSM_run4291_full_spectra.png|thumb|300px]]
+
| [[File:SBSM_run4291_full_spectra.png|thumb|250px]]
| [[File:PAS_run4282_full_spectra.png|thumb|300px]]
+
| [[File:PAS_run4282_full_spectra.png|thumb|250px]]
| [[File:LGU_run4321_full_spectra.png|thumb|300px]]
+
| [[File:LGU_run4321_full_spectra.png|thumb|250px]]
| [[File:LBP_run4317_full_spectra.png|thumb|300px]]
+
| [[File:LBP_run4317_full_spectra.png|thumb|250px]]
| [[File:ALP_run4298_full_spectra.png|thumb|300px]]
+
| [[File:ALP_run4298_full_spectra.png|thumb|250px]]
| [[File:PLS_run4370_full_spectra.png|thumb|300px]]
+
| [[File:PLS_run4370_full_spectra.png|thumb|250px]]
 
|}
 
|}
  

Revision as of 20:55, 20 September 2022

CyberShake Study 22.10 is a proposed study in Southern California which will include deterministic low-frequency (0-1 Hz) and stochastic high-frequency (1-50 Hz) simulations. We will use the Graves & Pitarka (2019) rupture generator and the high frequency modules from the SCEC Broadband Platform v22.4.

Status

This study is in the planning phase. We estimate calculations will begin in October 2022.

Data Products

Science Goals

Technical Goals

Sites

Velocity Model

High-frequency codes

For this study, we will use the Graves & Pitarka high frequency module (hb_high) from the Broadband Platform v22.4, hb_high_v6.0.5. We will use the following parameters. Parameters in bold have been changed for this study.

Parameter Value
stress_average 50
rayset 2,1,2
siteamp 1
nbu 4 (not used)
ifft 0 (not used)
flol 0.02 (not used)
fhil 19.9 (not used)
irand Seed used for generating SRF
tlen Seismogram length, in sec
dt 0.01
fmax 10 (not used)
kappa 0.04
qfexp 0.6
mean_rvfac 0.775
range_rvfac 0.1
rvfac Calculated using BBP hfsims_cfg.py code
shal_rvfac 0.6
deep_rvfac 0.6
czero 2
c_alpha -99
sm -1
vr -1
vsmoho 999.9
nlskip -99
vpsig 0
vshsig 0
rhosig 0
qssig 0
icflag 1
velname -1
fa_sig1 0
fa_sig2 0
rvsig1 0.1
ipdur_model 11
ispar_adjust 1
targ_mag -1
fault_area -1
default_c0 57
default_c1 34

Spectral Content around 1 Hz

We investigated the spectral content of the Broadband CyberShake results in the 0.5-3 second range, to look for any discontinuities.

The plot below is from WNGC, Study 15.12 (run ID 4293).

Spectral plot for WNGC from Study 15.12, target of 0.3676g @ 3 sec. Mean is in red.

Below is a plot of the hypocenters from the 706 rupture variations which meet the target.

WNGC run4293 target event hypos.png

These events have a different distribution than the rupture variations as a whole.

Fault Percent of target RVs Percent of all RVs
San Andreas 60 44
Elsinore 21 9
San Jacinto 13 8
Other 6 39

Additionally, 88% of the selected events have a magnitude greater than the average for their source. 4% are average, and 8% are lower.

Below is a spectral plot but which includes all rupture variations and the overall mean (in orange).

Spectral plot for WNGC from Study 15.12, all variations.

Additional Sites

We created spectral plots for 6 additional sites (SBSM, PAS, LGU, LBP, ALP, PLS), located here.

SBSM run4291 full spectra.png
PAS run4282 full spectra.png
LGU run4321 full spectra.png
LBP run4317 full spectra.png
ALP run4298 full spectra.png
PLS run4370 full spectra.png

Verification

Updates and Enhancements

Output Data Products

Computational and Data Estimates

Lessons Learned

Stress Test

Performance Metrics

Production Checklist

Science to-dos

  • Perform validation for Northridge, Chino Hills, Whittier, Landers, Hector Mine, and North Palm Springs
  • For each validation event, calculate BBP results, CS results, and CS results with BBP Vs30 values
  • Check for spectral discontinuities around 1 Hz
  • Decide if we should stick with rvfrac=0.8 or allow it to vary
  • Determine appropriate SGT, low-frequency, and high-frequency seismogram durations
  • Update high-frequency Vs30 to use released Thompson values

Technical to-dos

  • Integrate refactoring of BBP codes into latest BBP release
  • Switch to using github repo version of CyberShake on Summit
  • Update to latest UCVM (v22.7)
  • Switch to optimized version of rupture generator
  • Test DirectSynth code with fixed memory leak from Frontera
  • Switch to using Pegasus-supported interface to Globus transfers
  • Test bundled glide-in jobs for SGT and DirectSynth jobs

Presentations, Posters, and Papers